[. . . ] [PC] !' [DVI] !' [AV] !' [Component] !' [HDMI1] !' [HDMI2] !' [DisplayPort] !' [MagicInfo] !' [TV] Note · The [RGB/COMPONENT IN] port is compatible with RGB (PC) and Component signals. However, the picture may display abnormally if the connected external input signal is different from the selected video signal. · A TV tuner box (sold separately) must be connected to use the TV. Note Using MagicInfo · To use MagicInfo with an MXN-3, MPN-3 model, connect the MagicInfo output on the already included network box to [HDMI IN 2 (MAGICINFO)] on the product. [. . . ] Used to enter the password during the OSD adjustment or to use MagicInfo. DEL / GUIDE button The "-" button is used to select Digital channels. Note This button can only be used in TV mode while a TV tuner box (sold separately) is connected. / GUIDE button Introduction Selects a connected external input source or MagicInfo mode. Changing the SOURCE is only allowed for external devices that are connected to the LCD Display at the time. D. MENU DTV menu display Note This button can only be used in TV mode while a TV tuner box (sold separately) is connected. Up-Down Left-Right buttons INFO The Color button and the PC/DVI/HDMI/DP selection button. Moves from one menu item to another horizontally, vertically or adjusts selected menu values. Current picture information is displayed on the upper left corner of the screen. In TV mode, these buttons can be used to configure a list of channels. You can select the PC, DVI, HDMI or DP(DisplayPort) external input directly in a mode other than TV mode. Connect a set of audio cables between the AUDIO OUTPUT jacks on the camcorder and the [AV /COMPONENT AUDIO IN (R-AUDIO-L)] on the LCD Display . Press SOURCE on the product or remote control and select "AV". 4. Note The audio-video cables shown here are usually included with a Camcorder. (If not, check your local electronics store. ) If your camcorder is stereo, you need to connect a set of two cables. Connections Connecting Using a HDMI Cable 1. 2. Connect an HDMI cable to [HDMI IN 2 (MAGICINFO)] or [HDMI IN 1] on the product and the HDMI output port on a digital device. Press SOURCE on the product or remote control and select "HDMI1 / HDMI2" Note In HDMI mode, only PCM format audio is supported. Connecting Using a DVI to HDMI Cable Connect a DVI-HDMI cable to [HDMI IN 2 (MAGICINFO)] or [HDMI IN 1] and the DVI output port on the digital device. Contact a Service Center for problems that you cannot solve by yourself. Self-Test Feature Check 1. The figure shown below ("No Signal") appears on a black background when the LCD Display is working normally even though no video signal is detected: While in the SelfTest mode, the LED power indicator remains green and the figure moves around on the screen. If your LCD Display screen remains blank after using the previous procedure, check your video controller and computer system; your LCD Display is functioning properly. Turn off your LCD Display and reconnect the video cable; then turn on both your computer and the LCD Display. Warning Messages You can even view the screen at a resolution of 1366 x 786. However, you will receive the following message for a minute; You can choose to change the screen resolution or stay in the current mode during that time. If the resolution is more than 85Hz, you will see the black screen because the LCD Display does not support over 85Hz. Note Refer to Specifications > Preset Timing Modes for the resolutions or frequencies supported by the LCD Display. Maintenance and Cleaning 1) Maintaining the LCD Display Case. [. . . ] Ensure that the power cord is firmly connected and the LCD Display is on. (Refer to the Connecting a Computer) Q: A: "No signal" message. Ensure that the signal cable is firmly connected to the PC or video sources. (Refer to the Connecting a Computer) A: Q: A: A: Q: A: Ensure that the PC or video sources are turned on. [. . . ]